            ͻ
                                                              
                    Compex RL2000A PnP Ethernet Adapte        
              Copyright (C) 1996 by PDS. All Rights Reserved. 
                                                              
            ͼ


  Installation procedure to add remoteboot support on Windows NT Server
  v3.50/v3.51/v4.0 with Compex RL2000A-PnP adapters.

Before You Start
================
You should have the following items ready before you start:

1. Windows NT Server has been installed and you have
   administrator user right.

2. Latest distribution diskette for that Compex LAN Adapter
   and/or

3. FreedomROM PNPA v3.00d/v3.00c or higher installed on the adapter and
   configured to boot to "Windows NT" boot protocol.

4. Be sure to verify that your boot PROM is configured to boot from 
   LanServer/NT Server. To change, when your computer on booting display
   " Continue...... ",  press Ctrl-Enter to enter the protocol menu and
   select the " LAN Man/WINNT " option.

5. RL2000A-PNP is configured to Non-PnP mode. Run RLASET.EXE to configure.

** Note:- Throughout this procedure, Windows NT Server is assumed to
          have installed to C:\WINNT directory.


Installation Steps
==================

Step 1.
------
   Install the Remoteboot Service.
   -------------------------------
   Add NT Remoteboot software support and create the remoteboot image
   structure on the NT server. Make sure DLC and NetBEUI protocols are also
   installed.

   Remotebooting MS-DOS OS is the installation procedure explained below.

   For more details on NT Remoteboot software installation and creation
   of the remoteboot image structure, please refer to NT Server's manual, or
   NT Help document (if installed in NT Server during initial installation),
   or Windows NT Server CR-ROM help document.


Step 2:
-------
   Install the MS-DOS system files.
   --------------------------------
   1. Prepare a bootable disk and copy all the DOS utilities file to the disk
       e.g. MS-DOS v6.22,  that the workstaiton will boot.

   2. On Windows NT Server, log on as Administrator user or equivalent
      administrator user.

   3. Do the following sub-steps to copy the files.
      a) Copy all the files on bootdisk prepared in Step2-1 to the following
         directory,

           C:\> Copy A:\*.* C:\WINNT\RPL\RPLFILES\BINFILES\DOS622

      b) Change directory to C:\WINNT\RPL\RPLFILES\BINFILES\DOS622
	 and copy the system files in bootdisk to drive C 
         attrib -s -h  A:\io.sys
         attrib -s -h  A:\msdos.sys
         copy A:\io.sys  C:
         copy A:\msdos.sys  C:


Step 3:
------
   Start the Remoteboot Service.
   -----------------------------
   1. In the Control Panel, choose the Services icon.
   2. In the Services dialog box, select the Remoteboot service.
   3. Choose the Start button.


Step 4:
------
   Copy Compex RL2000A-PnP card profile files to NT Server.
   -------------------------------------------------------
   1. On Windows NT Server, log on to a user account that belongs
      to the Administrators local group.

   2. Make a directory RLPNPA under directory,

              C:\WINNT\RPL\BBLOCK\NETBEUI

   3. From Compex support disk or RL2000A-PnP distribution disk
      copy the following;

    a) Copy Compex RL2000A-PnP card profile files DOSBB.CNF and
       PROTOCOL.INI to the subdirectory,

              C:\WINNT\RPL\BBLOCK\NETBEUI\RLPNPA

    b) Copy RLPNPA.DOS to the subdirectory,

              C:\WINNT\RPL\BBLOCK\NDIS

    c) Copy RLPNPA.NIF to subdirectory,

              C:\WINNT\RPL\RPLFILES\BINFILES\LANMAN.DOS\DRIVERS\NIF


Step 5.
-------
   Creating Remoteboot configurations for RL2000A-PnP Adapter.
   ----------------------------------------------------------
   ** Note: Some entries are case sensitive. Please enter as indicated.


   1. Run RPLCMD utility to add a boot block record for the new
      RL2000A-PnP adapter. Please follow the sequence of commands
      to create boot block record:

               C:\WINNT\RPL> rplcmd

      Adapter Boot Config Profile Service Vendor Wksta [Quit]: b
      Add Del Enum: a
      BootName=RLPNPA_B
      VendorName=008048
      BbcFile=BBLOCK\NETBEUI\RLPNPA\DOSBB.CNF
         All other parameters are optional
      BootComment=Compex RL2000A-PnP
      WindowSize=0

      ** Note: VendorName should be exactly the same as the above,
      e.g., 008048.

   2. Run rplcmd utility to add the new configuration.
      Follow the sequence of commands to create the configuration:

               C:\WINNT\RPL> rplcmd

      Adapter Boot Config Profile Service Vendor Wksta [Quit]: c
      Add Del Enum: a
      ConfigName=RLPNPA_C
      BootName=RLPNPA_B
      DirName=DOS
      DirName2=DOS622
      FitShared=fits\dos622.FIT
      FitPersonal=fits\dos622p.FIT
         All other parameters are optional
      ConfigComment=MS-DOS 6.22 Compex RL2000A-PnP
      DirName3=
      DirName4=

      For BootName, enter the name of the boot block record you
      created in Step 5-1.


Step 6.
-------
   Create new Profiles.
   --------------------
   1. On Windows NT Server, log on to a user account that belongs
      to the Administrators local group.

   2. From the Remoteboot menu in Remoteboot Manager, choose
      New Profile.

   3. For the Profile Name, type a name for this profile, for
      example, DOS622RL.PNP

      ** Note: For the Profile name, if the server's RPL directory is
         on a FAT file system, use standard MS-DOS 8.3 format (eight
         characters, with an optional period and three more characters
         with no spaces or backslashes(\)).

   4. In the Configuration box, choose configuration you just
      created, e.g. MS-DOS 6.22 Compex RL2000A-PnP

   5. For the Description, type a comment for the profile. For example,

             Compex RL2000A-PnP boot MS-DOS v6.22

   6. Choose the OK button.


Step 7:
-------
   Adding a new workstation.
   -------------------------
   1. On Windows NT Server, log on to a user account that belongs
      to the Administrators local group.

   2. Start the Remoteboot Manager on the server.

   3. Start the remoteboot workstation.

   ** Note: The workstation does not actually boot, but it does send
            a boot request to the server.

   4. In Remoteboot Manager on the server, from the View menu,
      choose Refresh.

   5. In Remoteboot Manager, select the adapter record that has
      appeared with the network adapter ID number in place of the
      workstation name. 
      From the Remoteboot menu, choose Convert Adapters.

   6. In the Wksta Name box, type a name for the workstation. The
      name can have up to 15 characters. The Remoteboot service will
      create a Windows NT user account with this name, not for the
      user but for the workstation itself.

   7. In the Description box, type a comment that describes the
      workstation. The box already contains a comment provided by
      the network adapter itself.

   8. Choose a configuration type:

      Shared if this workstation can share its profile with other
      workstations.

      Personal if this workstation must use a personal copy of a
      profile so that you can customize the environment for the
      workstation.

   9. In the Wksta In Profile box, choose the profile just created,
      e.g., DOS622RL.PNP, for this workstation.

   10. In the TCP/IP Configuration box, enter appropriate addresses
       only if the workstation will use TCP/IP and will not use DHCP
       for automatic address handling.

   11. Choose the Add button.


Step 8:
------
   Testing the remote boot on the workstation.
   -------------------------------------------
   Cold boot the workstation. A remote boot logon prompt appears:

   Type remoteboot username, or press enter if it is <workstation>:


Step 9:
-------
   Remoteboot is successfully installed.


